Call us 24/7+254 700 031 732
0
0 KSh0.00
Call us 24/7+254 700 031 732
September 26, 2026 BY
IN Sensor

Camshaft Position Sensor Replacement

A camshaft position sensor replacement service addresses engine performance problems caused by a faulty sensor that monitors the position and speed of the camshaft. This sensor sends timing information to the engine control unit (ECU), helping coordinate fuel injection and ignition timing according to the engine’s design. When the sensor fails or provides inaccurate signals, you may experience difficulty starting the engine, rough idling, engine misfires, reduced power, or an illuminated check engine light. During this service, a technician scans the vehicle for diagnostic trouble codes, inspects the sensor and its electrical connections, and confirms whether the sensor is responsible for the fault. If the sensor is defective, it is replaced with a compatible component suited to your vehicle’s engine specifications. The technician then checks the sensor signal, clears relevant fault codes where appropriate, and verifies that the engine starts and runs correctly. Replacing a faulty camshaft position sensor helps restore accurate engine timing signals, supports reliable starting and smooth engine operation, and helps maintain proper engine management performance.

Read more
September 26, 2026 BY
IN Sensor

Air Cleaner Temperature Sensor Replacement

A car air cleaner temperature sensor replacement service addresses problems caused by a faulty sensor that measures the temperature of air entering through or around the air cleaner system. This sensor provides temperature information to the engine management system, helping it adjust engine operation according to incoming air conditions in vehicles equipped with this component. When the sensor fails or sends inaccurate readings, you may experience rough idling, reduced engine performance, increased fuel consumption, or an illuminated check engine light. During this service, a technician checks the relevant diagnostic trouble codes, inspects the sensor and its wiring, and confirms whether the sensor is causing the problem. If it is defective, the technician replaces it with a compatible component suited to your vehicle’s specifications. The sensor readings and related engine management functions are then checked to verify correct operation. Replacing a faulty air cleaner temperature sensor helps restore accurate temperature readings, supports proper engine management, and promotes reliable engine performance and efficient operation.

Read more
September 26, 2026 BY
IN Sensor

Air Charge Temperature Sensor Replacement

An air charge temperature sensor replacement service addresses problems caused by a faulty sensor that provides inaccurate readings of the temperature of air entering the engine. This sensor helps the engine control unit (ECU) calculate the appropriate fuel delivery and ignition timing based on incoming air conditions. When the sensor malfunctions, you may experience rough idling, reduced engine performance, poor fuel economy, difficulty starting, or an illuminated check engine light. During this service, a technician scans the vehicle for diagnostic trouble codes, checks the sensor wiring and electrical connections, and confirms whether the sensor is responsible for the problem. If the sensor is defective, it is replaced with a compatible component suited to your vehicle’s engine and specifications. The technician then checks the sensor readings, clears relevant fault codes where appropriate, and verifies that the engine management system is operating correctly. Replacing a faulty air charge temperature sensor helps restore accurate air temperature measurements, supports proper fuel and ignition control, and promotes smoother engine operation and efficient performance.

Read more
September 26, 2026 BY
IN Mirror

Car Door Mirror Replacement

A car door mirror replacement service restores your vehicle’s side mirror when it is cracked, broken, loose, or damaged beyond reliable use. Door mirrors help you monitor surrounding traffic, check adjacent lanes, and identify vehicles approaching from behind, making them essential for safer lane changes, overtaking, parking, and reversing. A damaged or missing mirror can reduce your field of view and make it more difficult to judge the position of other road users. During this service, a technician inspects the damaged mirror, checks the mounting points and adjustment mechanism, and determines whether the mirror glass, housing, or complete assembly needs replacement. A compatible replacement is then fitted securely, with electrical connections checked where applicable for power adjustment, heating, folding, or integrated indicator functions. The technician adjusts the mirror and tests its operation to confirm a clear, stable view of surrounding traffic. Replacing a damaged door mirror helps restore visibility, improves driver awareness, and supports safer vehicle manoeuvres on the road.

Read more
September 26, 2026 BY
IN Lights

Turn Signal Bulb Replacement

A turn signal bulb replacement service restores your vehicle’s indicator lights when a bulb burns out, flickers, or stops working properly. Turn signals help communicate your intention to turn or change lanes, allowing other drivers, cyclists, and pedestrians to anticipate your movements and respond accordingly. A faulty indicator bulb may cause the signal to flash unusually fast or fail to illuminate, making it harder for other road users to recognise your intentions. During this service, a technician inspects the affected indicator, identifies the faulty bulb, checks the bulb holder and electrical connections, and fits a compatible replacement suitable for your vehicle. The turn signals are then tested to confirm that they flash correctly and remain visible from the appropriate angles. The technician may also check the hazard warning lights where applicable. Replacing a faulty turn signal bulb helps restore dependable signalling, improves communication with other road users, and supports safer driving when turning, changing lanes, or navigating busy roads.

Read more
September 26, 2026 BY
IN Lights

Tail Light Lens Replacement

A tail light lens replacement service restores the protective outer cover of your vehicle’s rear light assembly when it becomes cracked, broken, cloudy, or damaged. The tail light lens helps protect the bulbs and internal components from moisture, dust, and road debris while allowing the rear lights to remain visible to drivers behind you. A damaged lens can allow water to enter the assembly, cause condensation, and reduce the effectiveness of the rear lighting system. During this service, a technician inspects the tail light lens and housing, checks for signs of moisture or damage, and determines whether the lens can be replaced separately or whether the complete assembly is required. The damaged component is replaced with a suitable part compatible with your vehicle, and the assembly is secured and checked for proper sealing. The rear lights are then tested to confirm correct illumination and visibility. Replacing a damaged tail light lens helps protect the lighting assembly, maintain clear rear light visibility, and prevent further damage caused by moisture and exposure to road conditions.

Read more
September 26, 2026 BY
IN Lights

Tail Light Bulb Replacement

A tail light bulb replacement service restores your vehicle’s rear lighting when a tail light becomes dim, flickers, or stops working completely. Tail lights help make your vehicle visible to drivers approaching from behind, particularly at night, during rain, and in other low-visibility conditions. When a bulb fails, other road users may have difficulty recognising your vehicle’s position and distance, increasing the risk of a rear-end collision. During this service, a technician inspects the rear light assembly, identifies the faulty bulb, checks the bulb holder and electrical connections, and installs a compatible replacement suited to your vehicle. The tail lights are then tested to confirm that they illuminate correctly when the exterior lights are switched on. The technician also checks the relevant light functions to ensure proper operation. Replacing a faulty tail light bulb helps restore rear visibility, supports compliance with applicable vehicle lighting regulations, and improves safety by making your vehicle more noticeable to other road users.

Read more
September 26, 2026 BY
IN Lights

Reverse Light Bulb Replacement

A reverse light bulb replacement service restores the rear reversing lights that illuminate when your vehicle is shifted into reverse gear. These lights help improve visibility behind the vehicle in low-light conditions and alert pedestrians and other drivers that you are reversing. When a reverse light bulb burns out, flickers, or stops working, it can become harder for others to recognise your reversing movements, increasing the risk of accidents in parking areas, driveways, and confined spaces. During this service, a technician inspects the reversing light assembly, identifies the faulty bulb, checks the bulb holder and electrical connections, and installs a suitable replacement compatible with your vehicle. The reversing lights are then tested to confirm that they illuminate correctly when reverse gear is selected. Replacing a faulty reverse light bulb helps restore rear visibility, improves awareness for other road users, and maintains the proper operation of your vehicle’s reversing light system.

Read more
September 26, 2026 BY
IN Lights

Reset Indicator Lights

A reset indicator lights service helps address dashboard warning or service lights that remain illuminated after the underlying issue has been repaired or the required maintenance has been completed. These indicators may relate to routine servicing, tyre pressure monitoring, oil maintenance, or other vehicle systems, depending on the warning displayed. During this service, a technician identifies the illuminated indicator, checks the vehicle’s maintenance requirements and diagnostic information, and determines whether a reset is appropriate. Where applicable, the technician uses the vehicle’s dashboard controls or a compatible diagnostic tool to reset the relevant service reminder or indicator according to the manufacturer’s procedure. The dashboard is then checked to confirm that the reset has been completed correctly. Resetting indicator lights after the necessary maintenance or repairs helps keep service reminders accurate, makes it easier to recognise new warnings, and supports proper vehicle maintenance. Warning lights linked to unresolved faults should be diagnosed and repaired rather than simply reset.

Read more
September 26, 2026 BY
IN Lights

License Plate Light Replacement

A license plate light replacement service restores the illumination that makes your vehicle’s registration plate visible in low-light conditions and at night. These lights are typically fitted above or beside the rear number plate and are designed to illuminate the plate whenever the relevant exterior lights are switched on. When a bulb burns out, flickers, or stops working, the registration plate may become difficult to read after dark, potentially affecting compliance with vehicle lighting regulations. During this service, a technician inspects the license plate light assembly, identifies the faulty bulb, checks the bulb holder and electrical connections, and installs a suitable replacement compatible with your vehicle. The light is then tested to confirm that it illuminates correctly when the exterior lights are activated. Replacing a faulty license plate light bulb helps maintain clear number plate visibility, supports compliance with applicable road regulations, and ensures your vehicle’s rear lighting system functions as intended.

Read more
Menu
Call us 24/7+254 700 031 732

Search for products

Back to Top
Product has been added to your cart